Reference · Updated November 2026
What is underglaze?
How underglaze differs from glaze, slip and engobe, when it goes on, what cone it fires to, how many coats it takes, and the one condition that makes it food safe.
By Travis Moher · Published November 17, 2026
Underglaze is a heavily pigmented, clay-based ceramic color that you paint on greenware or bisque and usually cover with a clear glaze. Commercial lines such as AMACO Velvet (cone 05 to 10) and Mayco Fundamentals (cone 06 to 10) go on in 2 to 3 coats, and they are food safe only when fired under a food-safe clear glaze. Unlike glaze, underglaze does not melt into a sealed glass on its own, which is exactly why painted lines stay sharp: the color stays where the brush put it.
The 3-coat rule
For solid, opaque color, plan on 2 to 3 coats, with 3 as the safe default on light clay. That is Mayco's direction for its Fundamentals underglazes, which can go on wet clay, greenware, or cone 04 bisque. Mayco also suggests turning the brush direction 90 degrees with each coat, so streaks from one coat are filled by the next. One thin coat gives a translucent, watercolor effect instead. Digitalfire notes that multiple coats are often needed for opacity and even color, which is why a single coat of a dark color can fire blotchy.
Underglaze vs glaze vs slip vs engobe
These four terms get used loosely, even by suppliers. The table separates them by what they are made of, when they go on, and what job they do on the finished pot.
| Material | What it is | Applied to | Firing | Role |
|---|---|---|---|---|
| Underglaze | Heavily pigmented ceramic color, normally stains in a clay and flux base | Wet clay, greenware, or cone 04 bisque (commercial lines) | Wide ranges, e.g. cone 05 to 10 (AMACO Velvet), cone 06 to 10 (Mayco Fundamentals) | Color layer, usually covered by clear glaze |
| Glaze | A glass-forming coating; a glossy glaze is a transparent base plus opacifiers and colorants | Usually bisqueware | Formulated for a specific cone | The finished, sealed surface |
| Slip | Predominantly liquefied clay | Greenware, wet to dry, depending on technique | Fires with the clay body it was made for | Decoration or surface texture; glazed or left bare |
| Engobe | Lower clay content than slip, closer to a glaze in structure; fires opaque | Can be formulated for any stage, including bisque | Formulated by cone range | Opaque coating for color, texture, or body adjustment |
Sources: Digitalfire glossary (underglaze, transparent glazes, engobe); Robin Hopper via Ceramic Arts Network (slip and engobe); AMACO and Mayco product directions (application surfaces and cone ranges).
Where the experts disagree
Robin Hopper, writing for Ceramic Arts Network, calls underglaze “basically the same thing” as an engobe: a lower-clay coating, more like a glaze in structure, that can be colored with any stain. Tony Hansen at Digitalfire draws the line the other way, stating that an underglaze is not the same as a slip or engobe, and describing engobes as thicker, fit-driven layers that adjust the body surface. Both are right about different products. A studio-mixed engobe is a coating you dip or pour; a commercial underglaze is a concentrated paint, heavy in stain, sold in 2 ounce jars for brushwork. For buying and applying, treat them as different materials.
When to apply underglaze: greenware or bisque
Commercial underglazes are made to go on at either stage. AMACO lists wet clay, greenware, or mature cone 04 bisque (1945°F / 1063°C) for its Velvet line, and Mayco lists the same three surfaces for Fundamentals. The practical differences:
- Leather-hard or greenware. Digitalfire says this is where underglaze bonds best. The color sinters onto the body during the bisque firing, the piece can be handled afterward without smudging, and fragile greenware is the only risk.
- Bisque. Sturdier to handle while you paint. Digitalfire notes the bond is not as good as on leather-hard ware, and recommends test-firing underglazes without an overglaze, even commercial ones, to see how well they hold.
- Two-firing method. Mayco describes painting the design, firing to cone 04, then applying a transparent glaze and firing to cone 06, with the note that colors come out lighter done this way.
Firing ranges, in cones and degrees
Underglazes are sold with wide ranges so one jar works with low-fire, mid-range, and high-fire clay. The range tells you the color will survive; it does not promise the color looks the same at both ends.
| Cone | °F | °C | What the makers say |
|---|---|---|---|
| Cone 06 | 1828°F | 998°C | Low end of Mayco Fundamentals; Mayco clear refire for earthenware is cone 06 to 05 |
| Cone 05 | 1888°F | 1031°C | Low end of AMACO Velvet; Velvets fire true to color as a cone 05/06 underglaze |
| Cone 04 | 1945°F | 1063°C | The bisque both makers list as an application surface |
| Cone 6 | 2232°F | 1222°C | Mid-range; AMACO says Velvets fire true to color at cone 6 |
| Cone 10 | 2345°F | 1285°C | Top of both ranges; AMACO says only some Velvet colors stay true at cone 10 |
Temperatures are Orton self-supporting cones at 108°F (60°C) per hour, from our kiln cone temperature chart. Notes paraphrase the published product directions from AMACO and Mayco. Mayco also says Fundamentals are formulated to mature at cone 06/05, with most colors holding up at higher temperatures.
The set the specs above describe
Price checked November 17, 2026. Affiliate link, so we may earn a commission at no cost to you.
AMACO Velvet Underglazes, 2 oz jars, 12-count setabout $123Rated cone 05 to 10, for wet clay, greenware or cone 04 bisque. AMACO lists food-safe status only under its LG-10 or HF-9 clear.View on Amazon →Is underglaze food safe?
Underglaze on its own is not a food surface. It fires porous, and Mayco says the clear glaze over it is what creates a durable, texture-free finish that meets FDA ceramic guidelines. The manufacturers' food-safety statements are all conditional:
- AMACO: all Velvet underglazes hold an approved food safety status when applied and fired under an approved clear glaze, named as AMACO LG-10 or HF-9.
- Mayco: Fundamentals are dinnerware safe under a compatible clear or other dinnerware-suitable glaze, and “finishedware producers bear responsibility for food-contact testing.”
- Digitalfire: describes underglazed pieces as functional and food safe when the clear layer isolates the pigment from food and is not crazed, so water cannot reach the body.
Digitalfire also documents the failure case: an underglaze that did not bond let the clear glaze over it pop off the inside of a bowl, which it calls a serious hazard on functional ware. If you underglaze interiors, test that exact underglaze, clear, clay and cone together first, and keep the clear uncrazed.
Exceptions and distinctions
- Low fire is the weak spot for bonding. Digitalfire notes that at cone 06, underglazes have almost no glass development to bond to the body. At low fire, the clear glaze does most of the holding.
- A wide range is not a promise of identical color. Digitalfire points out that stains can behave differently at each end of a range like cone 06 to 6, and AMACO says only some Velvet colors stay true at cone 10. Fire a test tile at your cone before a full piece.
- Underglaze is not slip. Slip is mostly clay and is matched to the body it decorates. A commercial underglaze is mostly water and pigment: Digitalfire measured commercial jars at specific gravities of 1.22 to 1.26, roughly two-thirds water.
- Shrinkage matters on greenware. Underglaze applied to greenware shrinks with the pot. Our clay shrinkage chart shows bodies shrinking 11% to 15% wet to fired, and Digitalfire's preference for leather-hard application reflects that the color bonds best while the body is still damp.
Free to use
Put this comparison chart on your site
Teaching a surface decoration class or writing a glazing guide? Copy the snippet below to embed the underglaze vs glaze vs slip vs engobe chart. It is self-contained and renders anywhere. The only ask is that you keep the small credit link back here.
Click inside the box, select all (⌘A / Ctrl-A), and copy.
Sources
- Tony Hansen, Digitalfire, “Underglaze”. Composition, best application stage, bonding at cone 06, wide-range caveats, food-safety conditions, and the specific gravity measurements.
- Robin Hopper, “Slip, Engobe, or Underglaze?” Ceramic Arts Network. Definitions of slip and engobe and application stages.
- AMACO, Velvet Underglazes. Cone 05 to 10 rating, application surfaces, true-to-color cones, food-safe status under LG-10 or HF-9.
- Mayco, Fundamentals Underglazes. Cone 06 to 10 range, 2 to 3 coats, application surfaces, clear refire cones, dinnerware statement.
- The Edward Orton Jr. Ceramic Foundation cone chart, via our kiln cone temperature chart, for the cone temperatures.
Questions
What is underglaze?
Underglaze is a heavily pigmented ceramic color, normally applied by brush, that goes on greenware or bisque and is usually covered with a clear glaze. Commercial underglazes are colored mostly with encapsulated ceramic stains, according to Digitalfire. Lines such as AMACO Velvet (cone 05 to 10) and Mayco Fundamentals (cone 06 to 10) are applied in 2 to 3 coats for solid color.
What is the difference between underglaze and glaze?
Glaze is the glass layer that seals and finishes the pot. Underglaze is a color layer that sits under the glaze and does not melt into a sealed glass on its own. Underglaze holds crisp painted lines because it does not flow, and a clear glaze over it adds gloss, deepens the color, and seals the surface.
Do you apply underglaze on greenware or bisque?
Either, with commercial underglazes. AMACO and Mayco both list wet clay, greenware, or cone 04 bisque as application surfaces. Digitalfire notes the bond is best on leather-hard ware and that application to bisque or dry ware is not as good, because underglazes only sinter during the bisque and bond mechanically. Greenware application also lets the color go through the bisque firing before you glaze.
How many coats of underglaze should I use?
Two to three coats for solid coverage, per Mayco's directions for its Fundamentals underglazes, with one coat for a translucent, watercolor look. Mayco suggests brushing each new coat at a right angle to the one before it for even coverage. Let each coat dry to the touch before the next.
Is underglaze food safe?
Only under a suitable clear glaze, and only as tested. AMACO states its Velvet underglazes hold an approved food safety status when applied and fired under its approved clears, LG-10 or HF-9. Mayco says its Fundamentals are dinnerware safe under a compatible clear glaze and that finished-ware producers are responsible for food-contact testing. Bare underglaze is porous, so do not leave it uncovered on surfaces that touch food.
Can you use underglaze without a clear glaze?
Yes, on decorative surfaces. AMACO says Velvets can be used with or without glaze, and Mayco notes Fundamentals fire matte without a clear glaze on earthenware. Leave bare underglaze on exteriors, sculpture, and tile, not on food-contact or drinking surfaces.
What temperature do you fire underglaze to?
Whatever cone your clay and clear glaze need, as long as it sits inside the underglaze's range. AMACO Velvet is rated cone 05 to 10 and Mayco Fundamentals cone 06 to 10. On Orton's chart at 108°F per hour that spans about 1828°F (cone 06) to 2345°F (cone 10). Expect some colors to shift or fade toward the top of a wide range.
Are these affiliate links?
One is. Austin Gallery is an Amazon affiliate, so if you buy through the product link here Amazon pays us a small commission at no extra cost to you. Every product specification on this page is attributed to its manufacturer. See our full affiliate disclosure.
Keep reading
- The kiln cone temperature chart: what cone 06, 04, 6 and 10 mean in °F and °C.
- Clay shrinkage and absorption rates: why the clay under the underglaze decides whether a pot is functional.
- The best electric kilns for home use: firing underglazed work at home.
- Gifts ceramicists actually use: underglaze sets are on the list.
Product ranges, application surfaces and food-safety statements are the published directions of the named manufacturer and apply to that product line only. Food safety of finished ware depends on the clay, clear glaze, and firing together; test before use. Compiled by the Austin Gallery editors, November 2026. Austin Gallery may earn a commission from product links on this page at no cost to you.
Cite this guide
Writers, framers, designers and students are welcome to quote this page. If you use one number, use this one:
Commercial underglazes such as AMACO Velvet (cone 05 to 10) and Mayco Fundamentals (cone 06 to 10) go on in 2 to 3 coats and are food safe only when fired under a food-safe clear glaze.
Suggested citation:
Austin Gallery, "What Is Underglaze? Underglaze vs Glaze vs Slip, and the 3-Coat Rule," updated November 2026. https://www.austingallery.org/blog/what-is-underglaze
More free charts: the Austin Gallery reference library.