Austin Gallery
WoodworkingNovember 17, 2026Updated November 17, 202611 min read

Best Router Bits (2026)

Whiteside, Freud, CMT, Bosch, and Yonico sets, plus the spiral, roundover, and flush trim bits worth buying on their own, and how to choose between 1/4 and 1/2 inch shanks.

By Austin Gallery · How we research

★ Our Top Pick

Whiteside 401 Basic 7-Piece Router Bit Set (1/2 in. Shank)

Whiteside 401 Basic 7-Piece Router Bit Set (1/2 in. Shank)

Seven bits you will use, on 1/2 in. shanks.

$141rated 4.8/5 in our review

Not sure yet? Compare all 8 picks below ↓

The best router bit set of 2026 is the Whiteside 401 (about $141): seven bits on 1/2 inch shanks from the maker experienced woodworkers recommend most, with no filler. For broader coverage, the Freud 91-100 13-piece set ($244) is the upgrade and the CMT 13-piece ($180) the mid-price alternative. Trim router owners should buy the Bosch 10-piece 1/4 inch set ($103), and on a budget the Yonico 1/4 inch set ($50) is good enough to learn on.

1/4 vs 1/2 inch shank

The shank must match your router's collet. Trim and palm routers (Makita RT0701C, Bosch Colt, DeWalt DWP611) take 1/4 inch shanks only. Full-size routers (Bosch 1617EVS, DeWalt DW618) usually ship with both a 1/4 and a 1/2 inch collet.

When you have the choice, pick 1/2 inch. A 1/2 inch shank has four times the cross-sectional area of a 1/4 inch shank, so it is far stiffer, vibrates less, leaves a smoother cut, and is less likely to snap under a big profile. Use 1/2 inch for anything over about 1 inch in diameter, for raised panel bits, and for every bit in a router table. Use 1/4 inch for trim routers and small edge profiles, where it is perfectly adequate.

Not sure which router you need? See our best wood routers guide and trim router vs plunge router. Every product link goes to Amazon with our affiliate tag; we earn a small commission at no cost to you. We compared listings, stated specifications, and owner feedback patterns; we did not physically test these.

Best Overall SetOur Pick

Pieces

7

Shank

1/2 in.

Maker

Whiteside (USA)

Part numbers

1804, 1901, 2008, 2305, 1058, 1067, 2405

Fits

Full-size routers with a 1/2 in. collet

Pros

  • Whiteside carbide and grinding quality
  • 1/2 in. shanks for stiffness and less chatter
  • Only bits you will use
  • Each bit is replaceable individually

Cons

  • Pricier per bit than mass-market sets
  • Will not fit 1/4 in. trim routers
  • Intermittent stock

Buy fewer, better bits. The most common mistake with router bits is buying a 50 or 70 piece set, using six of the bits, and finding those six dull after a few projects. The Whiteside 401 takes the opposite approach: seven of Whiteside's core bits, on 1/2 inch shanks, from a maker whose bits are the ones experienced woodworkers recommend most consistently. Our best wood routers guide pairs it with the full-size routers that can use it.

Why 1/2 inch shank: a 1/2 inch shank has four times the cross-section of a 1/4 inch shank, so it flexes less, chatters less, and runs cooler. On a full-size router or in a router table, choose 1/2 inch every time.

For a trim router, Whiteside sells the smaller Whiteside 404 compact set (about $104) with a flush trim, a 1/8 inch roundover, a template bit, and a 45 degree chamfer.

Our Pick

Seven bits from the American maker most serious woodworkers buy individually, on 1/2 inch shanks. Fewer bits than the big sets, and every one of them is a bit you will use.

Buy this if you own a full-size router like the Bosch 1617EVS or DeWalt DW618 and want a small set of bits that cut clean and last, rather than a big box of bits you will never touch.

What we don't like

Seven bits at about $20 each is not cheap, and the 1/2 inch shanks will not fit a 1/4 inch trim router. Stock has been thin, so check availability.

Best Larger SetUpgrade Pick

Pieces

13

Maker

Freud

Model

91-100

Best for

Broad profile and joinery coverage

Pros

  • Freud carbide and coatings
  • Thirteen useful bits
  • A complete first kit

Cons

  • About $244
  • Some bits used rarely
  • Check shank size before buying

Freud is the other brand pros buy without hesitation. The 91-100 is Freud's 13-piece set, and it covers more ground than the Whiteside 401: more profiles and more straight and joinery bits. If you plan to do edge work, grooves, and joinery from day one, it is the better single purchase.

Fit: check the listing for the shank size before buying, and match it to your router's collet. For the full 26 bits, the Freud 92-100 Artisan set (about $470) is the do-everything kit.

Upgrade Pick

Thirteen Freud bits covering the profiles and straight bits most furniture work needs. The step up when you want broader coverage than Whiteside's seven without dropping to budget carbide.

Buy this if you want one purchase to cover edge profiles, grooves, and joinery bits with quality carbide.

What we don't like

About $244 is real money, and like any set it includes a few bits you may use rarely. Confirm the shank size on the listing for your router.

Best Mid-Price Set

Pieces

13

Maker

CMT Orange Tools

Model

800.505.11

Best for

Broad coverage at a mid price

Pros

  • Professional-grade brand
  • Thirteen bits
  • About $64 less than the Freud

Cons

  • Fewer single-bit replacements in stock
  • Check shank size
  • Some bits used rarely

CMT is the professional brand people forget to check. The 800.505.11 matches the Freud 91-100 bit for bit in count, for about $180. Owner feedback on CMT carbide is consistently positive, and the orange non-stick coating helps keep pitch from building up on the cutters.

Fit: confirm the shank size on the listing against your router's collet before ordering.

CMT's 13-piece set, from the Italian maker known for its orange-coated bits. Freud-class coverage for about $64 less.

Buy this if you want a 13-bit set from a professional brand and the Freud is over budget.

What we don't like

Less widely stocked than Freud for single-bit replacements, and as with any set, confirm the shank size for your router.

Best Set for Trim Routers

Pieces

10

Shank

1/4 in.

Carbide

Micrograin

Case

Included

Fits

Trim and palm routers, any 1/4 in. collet

Pros

  • Fits every trim router
  • Micrograin carbide
  • Storage case
  • Brand-name quality

Cons

  • 1/4 in. shanks flex more
  • Lighter passes on big profiles
  • Costs more than Yonico

Match the set to the router. Trim routers accept only 1/4 inch shanks, so a 1/2 inch set is useless with them. This Bosch set gives a trim router owner ten carbide bits in the right shank size and a case to keep them in. If you are still choosing a router, our trim router vs plunge router comparison covers the decision.

Ten micrograin carbide bits on 1/4 inch shanks in a storage case, from the maker of the routers many of these bits end up in. A sensible first set for a trim or palm router.

Buy this if your router is a 1/4 inch collet trim router like the Bosch Colt, Makita RT0701C, or DeWalt DWP611.

What we don't like

1/4 inch shanks flex more than 1/2 inch ones, so take lighter passes with larger profiles.

Austin Art Insider

Free weekly guide to galleries, exhibitions & collecting in Austin.

Best Budget SetBudget Pick

Shank

1/4 in.

Carbide

Tungsten carbide tipped

Model

17150q

Fits

Trim routers and any 1/4 in. collet

Best for

Learning and occasional use

Pros

  • About $50
  • Fits any trim router
  • Lets you try many profiles cheaply

Cons

  • Dulls sooner than name brands
  • Less consistent balance
  • Not for production work

A budget set is a way to find out what you use. Most woodworkers end up running four or five profiles over and over. A Yonico set lets you try all of them for about $50, and when the roundover and the flush trim dull, you replace just those two with a Whiteside or Freud bit. Yonico also sells a 70-piece 1/2 inch shank set (about $162) for full-size routers, but at that price we would buy the Whiteside 401.

Budget Pick

The budget set that owner feedback treats as good enough to learn on: carbide-tipped bits on 1/4 inch shanks for about $50.

Buy this to learn which profiles you use, then replace those few with Whiteside or Freud bits as they dull.

What we don't like

Carbide quality and balance are a step below the name brands, and edges dull sooner. Not the set for hardwood production work.

Best Spiral Bit

Type

Up spiral

Diameter

3/8 in.

Cut height

1-1/4 in.

Shank

1/2 in.

Carbide

TiCo Hi-Density

Max RPM

24,000

Pros

  • Clears chips from deep cuts
  • Cuts cooler than a straight bit
  • Clean mortise walls

Cons

  • Can fray the top edge
  • Solid carbide is brittle if dropped
  • 1/2 in. collet needed

The first bit to buy beyond a set. A straight bit shears; a spiral bit slices and lifts. In a mortise or a deep groove, the upcut spiral pulls chips up and out so the bit does not recut them, which keeps it cooler and leaves smoother walls. It is the bit plunge routers were made for.

A solid carbide upcut spiral that pulls chips out of the cut, the right bit for mortises, grooves, and dadoes. Cleaner and cooler than a straight bit in deep cuts.

Buy this for a plunge router or router table if you cut mortises, grooves, or dados.

What we don't like

Upcut spirals can lift fibers at the top edge of the cut; use a downcut spiral where the top face must stay crisp.

Best Roundover Bit

Profile

Roundover

Radius

3/8 in.

Cutters

4 (Quadra-Cut)

Shank

1/4 in.

Coating

Perma-Shield

Fits

Trim and full-size routers with a 1/4 in. collet

Pros

  • Four cutters for a smoother finish
  • Fits trim routers
  • The profile you use most

Cons

  • Pricey for one bit
  • Single radius
  • 1/2 in. shank versions cost more

Spend on the bit you run the most. For most shops that is a 3/8 inch roundover. Freud's Quadra-Cut design uses four cutters instead of two, which the listing credits with a smoother finish, and the Perma-Shield coating resists pitch. On a 1/4 inch shank it runs in any trim router. Freud also makes a 3/8 inch roundover on a 1/2 inch shank (about $34) for table use.

Freud's four-cutter roundover, which the listing pitches for a flawless finish. The roundover is the most-used router profile, and this is the one to own.

Anyone who rounds over edges on tables, shelves, and boxes, which is everyone with a router.

What we don't like

About $33 for one profile, more than a whole budget set. Worth it for the bit you use most.

Best Flush Trim Bit

Type

Bearing flush trim

Diameter

3/8 in.

Cutting length

1 in.

Maker

Whiteside

Best for

Edge banding, laminate, template routing

Pros

  • About $22
  • Whiteside quality
  • The most-used trim router bit

Cons

  • 1 in. cutting length
  • Bearing needs occasional cleaning

If you buy one single bit, buy this one. A flush trim bit rides its bearing along a template or the face of a panel and cuts the overhang flush: edge banding, laminate, and copies of a pattern. Whiteside's version costs about $22. The Freud 42-100 (about $16) is a good alternative, and Amana's 45475 (about $30) states a 1/4 inch shank on its listing.

A bearing-guided flush trim bit that trims edge banding, laminate, and template-cut parts flush to the guide. The cheapest bit here and one of the most used.

Everyone with a router. Flush trimming is the job trim routers are named for.

What we don't like

The 1 inch cutting length limits it to stock up to that thickness in one pass.

How we
chose

How we chose these bits:

  • Brand quality first. Whiteside, Freud, and CMT carbide is consistently praised in owner feedback for edge life and finish. We ranked those sets above mass-market sets even when the count is lower.
  • Shank match. We say which sets fit trim routers and which need a full-size router, because a bit that does not fit the collet is useless.
  • Bits you will use. We favored sets with fewer, more useful bits over 50 or 70 piece boxes.
  • Stated specifications only. Diameters, radii, shank sizes, and part numbers come from the listings; where a listing does not state the shank, we tell you to check.
  • Verified listings. Every bit, price, and image is verified against the live Amazon catalog at the time of writing. We compared listings, stated specifications, and owner feedback patterns; we did not physically test these.

Share this guide

Share

Common Questions

Frequently Asked Questions

Have art
to sell?

Austin Gallery specializes in selling inherited art, estate collections, and fine art with zero upfront fees. Get a free evaluation today.