Lighting Guide
Picture Light Size Guide: The Half to Two-Thirds Rule
A picture light should be one-half to two-thirds the width of the artwork, measured without the frame, aimed from about 30 degrees, at 2700K to 3000K with a CRI above 90. Keep originals near 50 lux if they are on paper and no higher than about 150 lux if they are paintings.
By Travis Moher · Published November 17, 2026
The half to two-thirds rule
Measure the image, not the frame. Perfect Picture Lights, a dealer that has sold picture lights for decades, sizes the fixture at one-half to two-thirds of the artwork excluding its frame, and about half the width for portrait-format pieces. The frame is decoration around the thing being lit; sizing to it gives a light that looks too big and throws light onto the moulding instead of the picture.
The ratio is not fixed across sizes. Per the same dealer's sizing guide, a traditional light with a 2 inch shade holds at half the image width up to about 30 inches; above that the ratio climbs, so a 60 inch image takes a light about 40 inches wide. A slimline light with a 1 inch shade throws a narrower beam, so the half-width rule only holds to about 18 inches; a 30 inch image takes about 20 inches and a 60 inch image about 45 inches.
| Image width (no frame) | Traditional, 2 in shade | Slimline, 1 in shade |
|---|---|---|
| 12 in (30 cm) | 6 in (15 cm) or more | 6 in (15 cm) or more |
| 18 in (46 cm) | 9 in (23 cm) or more | 9 in (23 cm) |
| 20 in (51 cm) | 10 in (25 cm) or more | About 11 in (28 cm) |
| 30 in (76 cm) | 15 in (38 cm) or more | About 20 in (51 cm) |
| 60 in (152 cm) | About 40 in (102 cm) | About 45 in (114 cm) |
Ratios from Perfect Picture Lights; the 20 inch slimline row is interpolated between its 18 inch and 30 inch examples. Dark paintings, bright rooms and weaker LEDs push toward the wider end.
Arm length vs frame height and depth
Width spreads the light sideways; the arm decides how far down it reaches. Two constraints set the arm. First, depth: the standoff must be greater than the thickness of the frame, or the top rail shades the upper part of the picture. Perfect Picture Lights' default puts the bottom of the shade about 1 inch above the top of the frame and notes that unusually tall art needs a greater standoff.
Second, height. No maker we found publishes a formula, so here is our rule of thumb from simple geometry: to hit the center of the art from about 30 degrees, the light head needs to sit roughly 0.58 times half the frame height out from the face of the art. That works out to about 5 inches for a 16 inch tall piece, 7 inches for 24 inches, 10 inches for 36 inches and 14 inches for 48 inches. Past about 36 inches of height, a single frame light struggles to reach the bottom edge evenly, and a ceiling light or a pair of lights is the better answer.
Distance and the 30 degree angle
Perfect Picture Lights recommends aiming at about 30 degrees to reduce glare, the angle lighting designers commonly cite for wall-hung art, measured off vertical. Steeper than that and frames cast long shadows and texture looks exaggerated; shallower and reflections off glazing bounce toward the viewer.
For ceiling-mounted lights, the angle turns into a distance from the wall. Take the ceiling height, subtract 57 inches for the center of the art, and multiply by 0.58 (the tangent of 30 degrees).
| Measure | Number | Note |
|---|---|---|
| Light width vs image width | 1/2 to 2/3 (no frame) | Ratio rises on wide art |
| Arm standoff | More than frame thickness | Default shade about 1 in above frame |
| Aim angle | About 30 degrees | Less glare, short frame shadow |
| Ceiling light offset, 8 ft ceiling | About 22 in | 57 cm from wall |
| Ceiling light offset, 9 ft ceiling | About 29 in | 75 cm from wall |
| Ceiling light offset, 10 ft ceiling | About 36 in | 92 cm from wall |
| Color temperature | 2700K to 3000K | Warm white |
| Color rendering | CRI above 90 | LED, not halogen |
| Light on sensitive originals | About 50 lux | Paper, photos, textiles |
| Light on most paintings | Up to about 150 lux | Darker details |
Color temperature and CRI
Use 2700K to 3000K warm white with a color rendering index above 90; that is the dealer guidance for accent lighting, and the warm end flatters most paintings. Low CRI LEDs flatten reds and earth tones first. Choose LED for the heat alone: Perfect Picture Lights notes halogen generates enough heat that it may eventually damage paintings. For the wider picture, including track and ceiling options, see our guide to how to light artwork at home and our best track lighting for art picks.
Lux on originals
Light damage is cumulative and irreversible. The Canadian Conservation Institute notes most colours can be seen reasonably well at 50 lux, with darker detail needing more, and it holds the most sensitive pigments to about 50 lux. The Northeast Document Conservation Center gives 50 to 150 lux for three to four months of display and an ideal annual dose of 50,000 lux hours for light-sensitive work: at 50 lux for 10 hours a day that is used up in 100 days, at 100 lux in 50 days. CCI also caps UV at 75 microwatts per lumen where it cannot be removed entirely.
A phone light meter app is close enough for a home check (NEDCC: one footcandle is about 11 lux). Put a timer on the light, and for paper, photographs and textiles keep it off when no one is in the room. Our guide to protecting art from fading covers glazing and the rest of the light budget.
Exceptions and distinctions
- •Frame mount vs wall mount. CCI says picture lamps attached to frames are rarely successful: they light unevenly and can overheat the painting. Mount on the wall above the frame where you can, and never screw into an antique or gilded frame.
- •Glazed work. Glass and acrylic throw a reflection of the light itself. Hold the 30 degree angle and consider anti-reflective glazing rather than a brighter lamp.
- •Hot spots. CCI warns that lights directed at a painting can create damaging warm spots. Feel the surface after an hour on; if the top edge is warmer than the bottom, move the light out or dim it.
- •Portrait vs landscape. A tall portrait-format piece needs reach more than width; about half the width plus a longer arm, or light from the ceiling.
- •Battery lights. Fine for prints and walls with no power. Output fades as batteries drain, so judge the color with fresh batteries.
- •Over a fireplace. Heat from below plus a lamp above is the worst combination for an original. See art above a fireplace.
Free to use
Put this picture light chart on your site
Writing about lighting, framing or decorating with art? Copy the snippet below. It renders a clean, responsive table anywhere. The only ask: keep the small credit link to Austin Gallery.
Click inside the box, select all (Cmd A or Ctrl A), and copy. Includes one credit link back to this page.
Questions people ask
What size picture light do I need?
Choose a light one-half to two-thirds the width of the artwork itself, measured without the frame. A 20 inch (51 cm) wide image takes a light of at least 10 inches (25 cm); a 60 inch (152 cm) image takes one about 40 inches (102 cm) wide.
Should a picture light be as wide as the frame?
No. Measure the image, not the frame. Perfect Picture Lights sizes lights to the artwork excluding its frame, at one-half to two-thirds of that width; sizing to the frame produces a fixture that looks oversized.
How far should a picture light arm extend?
Far enough to clear the frame: the standoff must be greater than the frame's thickness, or the frame will shade the top of the picture. Taller art needs a longer reach. Our geometry rule of thumb: to aim at the center from 30 degrees, the head sits about 0.58 times half the frame height out from the face, roughly 7 inches (18 cm) for a 24 inch tall piece.
What is the 30 degree rule for lighting art?
Aim light at the artwork from about 30 degrees off vertical. It reduces glare on glazing and avoids long frame shadows. For a ceiling light, that puts the fixture about 0.58 times the drop to the art center out from the wall: roughly 22 inches (57 cm) on an 8 foot ceiling and 29 inches (75 cm) on a 9 foot ceiling.
What color temperature is best for a picture light?
2700K to 3000K warm white with a CRI above 90, as Perfect Picture Lights recommends for accent lighting. Use LED: it adds little heat, while halogen runs hot enough to damage paintings over time.
How many lux should a painting get?
Conservation guidance keeps sensitive work around 50 lux and most paintings no higher than about 150 lux. NEDCC sets an ideal annual dose of 50,000 lux hours for light-sensitive work, which 50 lux for 10 hours a day uses up in 100 days.
Are picture lights bad for paintings?
They can be. The Canadian Conservation Institute says picture lamps attached to frames are rarely successful because they light unevenly and can overheat the painting. A cool LED, a wall mount instead of a frame mount, a timer and a check for hot spots manage most of the risk.
Sources
- Perfect Picture Lights, Choosing the Right Size Picture Light. Half the image width up to 30 in (traditional) or 18 in (slimline); 60 in image takes about 40 in traditional, 45 in slimline.
- Perfect Picture Lights, How to Hang a Picture Light. 1/2 to 2/3 of the artwork excluding frame; standoff greater than frame thickness; 30 degree aim; CRI above 90; 2700K to 3000K; halogen heat.
- Canadian Conservation Institute, Environmental Guidelines for Paintings (CCI Notes 10/4). About 50 lux for sensitive pigments, more for dark detail; UV under 75 microwatts per lumen; frame-attached lamps rarely successful.
- Northeast Document Conservation Center, Leaflet 2.5: Protecting Paper and Book Collections During Exhibition. 50 to 150 lux; 50,000 lux hours a year; 1 footcandle about 11 lux.
- Canadian Conservation Institute, Basic care: Paintings. Lights directed at a painting can create damaging hot spots.
Sizing ratios come from a picture light dealer's published guidance; light levels come from published conservation guidance as of November 2026. Arm reach and ceiling offsets are Austin Gallery's calculations from the 30 degree angle, not manufacturer specifications. Follow your fixture's installation instructions.
Cite this guide
Writers, framers, designers and students are welcome to quote this page. If you use one number, use this one:
A picture light should be one-half to two-thirds the width of the artwork, measured without the frame, aimed from about 30 degrees at 2700K to 3000K with a CRI above 90.
Suggested citation:
Austin Gallery, "Picture Light Size Guide: The Half to Two-Thirds Rule," updated November 2026. https://www.austingallery.org/blog/picture-light-size-guide
More free charts: the Austin Gallery reference library.