Hanging & Installation
How to Hang Art on Brick, Plaster, Tile and Concrete: The 4:1 Rule
In concrete, a 3/16 inch concrete screw set 1 inch deep has an average ultimate shear value of 720 lb; at the standard 4:1 safety factor, plan on about 180 lb (82 kg) per screw. Block holds less, brick varies, plaster wants hooks or anchors instead of nails, and tile is only as strong as what is behind it.
By Travis Moher · Published November 17, 2026
Most hanging advice assumes drywall. Austin has plenty of walls that are not: exposed brick in downtown lofts, concrete in newer condos, plaster in older homes, and tile in kitchens and baths. Each one needs a different fixing, and drywall weight ratings do not transfer to any of them. Here is the method and the published capacity for each wall type, with the safety margin we use when we install.
Fixing method and capacity by wall type
| Wall | Method | Working capacity | Notes |
|---|---|---|---|
| Poured concrete (2,000 psi) | 3/16 in concrete screw, 5/32 in (4 mm) bit, 1 in (2.5 cm) min embedment | About 180 lb (82 kg) shear, 150 lb (68 kg) pull-out per screw | Solid. Published ultimate: 720 lb shear, 600 lb pull-out |
| Medium weight concrete block | 3/16 in concrete screw, 5/32 in bit | About 183 lb (83 kg) shear, 85 lb (39 kg) pull-out | Hollow cores. Hit the solid face shell |
| Lightweight concrete block | 3/16 in concrete screw, 5/32 in bit | About 100 lb (45 kg) shear, 55 lb (25 kg) pull-out | Softest masonry. Use two fixings for heavy work |
| Brick | Masonry bit plus plastic anchor (light) or concrete screw (heavy) | Not published as one figure; test a fixing | Mortar is easy to patch; brick face holds better |
| Brick, no drilling | Brick clip | Up to 25 lb (11 kg) per clip | Fits 2-1/8 to 2-1/2 in (5.4 to 6.4 cm) brick; needs recessed mortar |
| Plaster and lath, light | Adhesive strips | Under 16 lb (7 kg) | Smooth, sound plaster only |
| Plaster and lath, medium | Steel picture hook or plaster hook, tapped in | Under 30 lb (14 kg) | Tape the spot; never hammer hard |
| Plaster and lath, heavy | Plaster-rated anchor, screw into stud, or rail system | Anchor rating; stud is strongest | Pre-drill; plaster cracks around a struck nail |
| Picture rail molding | Picture rail hook and cord | 25 lb (11 kg) per hook, typical | Lowest-rated part sets the limit; use two hooks |
| Ceramic or porcelain tile | Drill through tile into stud or backer board | What is behind the tile sets the capacity | Carbide bit, lowest speed, water cooling |
Concrete and block figures are 25% of the average ultimate values in published Tapcon data (3/16 inch screw, 1 inch embedment), rounded. Plaster figures from Family Handyman. Brick clip from the Adams product specification. Rail hook from Picture Hang Solutions. Kilogram conversions are rounded.
The 4:1 rule
Fastener tables usually list ultimate loads: the average force at which the fixing fails. The published Tapcon specifications say a safety factor of 4:1, or 25%, is generally accepted as a safe working load, and that the values are averages, not guarantees. So divide any ultimate number by four before you hang anything on it.
Two more points matter for art. A picture on a wall loads its fixings mostly in shear(downward along the wall), not pull-out, and shear values are usually the higher of the two. And a frame hung from two fixings spreads its weight, so two screws at 180 lb each give real margin for a heavy mirror or large canvas.
Concrete and concrete block
Poured concrete is the strongest wall in a house. Drill with a hammer drill and a 5/32 inch (4 mm) carbide bit for a 3/16 inch concrete screw, at least 1 inch (2.5 cm) deep and no more than 1-3/4 inches (4.4 cm), per the Tapcon specification. Published ultimate values in 2,000 psi concrete are 600 lb pull-out and 720 lb shear for a 3/16 inch screw, and 750 lb and 900 lb for a 1/4 inch screw.
Concrete block is hollow, and values drop. For a 3/16 inch screw, Tapcon lists 340 lb pull-out and 730 lb shear in medium weight block, and 220 lb and 400 lb in lightweight block. Keep the hole in the solid face shell of the block, not in the hollow core behind it.
Brick
Drill the mortar joint or the brick itself, with a carbide masonry bit sized to your anchor. Mortar is softer, quicker to drill and easy to patch when you move the piece. Solid brick gives the stronger hold for heavy frames and mirrors. Bob Vila recommends marking with chalk, drilling only as deep as the anchor, and using two anchors for a heavy glass-fronted frame.
Fastener makers do not publish a single brick number because brick varies so much, from hard modern face brick to soft, crumbly old brick. Our rule of thumb: set one fixing, load it by hand well past the frame's weight, and only then hang the art.
No-drill option. Brick clips hook over a brick and grip the top and bottom edges. The Adams standard clip holds up to 25 lb (11 kg) and fits bricks 2-1/8 to 2-1/2 inches (5.4 to 6.4 cm) high. They only work where the mortar is recessed enough to grip.
Plaster and lath
Plaster in older homes is keyed into wood lath: wet plaster squeezed through the gaps and hardened behind it. Family Handyman warns that hammering a nail can break those keys and separate the plaster from the lath. Its weight guide:
- •Under 16 lb (7 kg): adhesive strips or hooks, which leave no marks.
- •Under 30 lb (14 kg): steel picture hooks or plaster hooks. Put painter's tape over the spot and tap the nail in rather than hammering it.
- •Heavier: anchors rated for plaster, a screw into a stud, or a gallery rail system screwed into studs near the ceiling.
Hollow vs solid. Plaster over lath is hollow behind the lath. Plaster applied directly to brick or block, common in some older and masonry houses, is solid behind. If your bit hits hard resistance and throws red or gray dust after the plaster, you are in masonry, and the concrete and brick methods above apply.
Picture rail
Many older homes have a picture rail molding near the ceiling, built so art could hang without touching the plaster. Hooks sit on the rail and hang the frame on cord or cable. Picture Hang Solutions rates its rail hooks at 25 lb (11 kg) and stresses that the lowest-rated component sets the limit for the whole system. Use two hooks per frame. The molding itself is not rated, so check that it is firmly nailed before trusting it with anything heavy.
Tile
Tile is a surface, not a structure. Drill through it and the fixing must continue into a stud or backer board behind, which is what carries the load. Bob Vila's method: a cross of painter's tape so the bit does not skate, a light center punch to break the glaze, a carbide-tipped masonry bit at the drill's lowest speed with moderate pressure, and water to keep the bit cool. Do not use hammer mode on tile. In a bathroom, keep in mind that the art itself has humidity limits; see our framed art in a bathroom guide.
Exceptions and distinctions
- •Drywall numbers do not apply. A drywall anchor in brick or plaster holds unpredictably. For drywall itself, see how much weight drywall can hold.
- •The hook is often the weak link, not the wall. A concrete screw rated for 180 lb does you no good under a picture hook or wire rated for 20. Every part of the chain needs to clear the frame's weight. Our picks for strong hardware are in the best picture hangers for heavy frames.
- •Adhesive strips are for smooth surfaces. They fail on rough, unsealed brick and on dusty or flaking plaster. Rated weights assume clean, smooth, sound surfaces.
- •Old brick and old mortar are softer. In older buildings, crumbling mortar will not hold a plastic anchor. Go into the brick face, or use a rail or a floor easel.
- •Check for services first. Drill only as deep as the anchor. Pipes and wiring can run in masonry chases and behind tile.
Once the fixing is in, the height is the same on every wall: see how high to hang art.
Free to use
Put this wall hanging chart on your site
Writing about decorating, renovation or hanging art? Embed our wall type chart for your readers. Copy the snippet below. It renders a clean, responsive table anywhere. The only ask: keep the small credit link to Austin Gallery.
Click inside the box, select all (⌘A or Ctrl+A), and copy. Includes one credit link back to this page.
Frequently asked questions
How much weight can a concrete screw hold?
A 3/16 inch Tapcon set 1 inch into 2,000 psi concrete averages 600 lb ultimate pull-out and 720 lb ultimate shear, according to published Tapcon data. At the standard 4:1 safety factor, that is about 150 lb pull-out and 180 lb shear per screw.
Should I drill into the brick or the mortar to hang a picture?
Mortar for light and medium pieces, because it drills easily and patches invisibly. Brick face for heavy pieces, because solid brick holds better. Use a carbide masonry bit sized to the anchor, and two anchors for a heavy glass-fronted frame.
How do you hang a picture on brick without drilling?
Use brick clips that grip the brick above and below. A standard Adams brick clip holds up to 25 lb (11 kg) and fits bricks 2-1/8 to 2-1/2 inches (5.4 to 6.4 cm) high. Clips need a recessed mortar joint to grip.
What is the best way to hang pictures on plaster walls?
Do not hammer nails into plaster; it can break the keys that hold plaster to the lath. Family Handyman recommends adhesive strips under 16 lb (7 kg), tapped-in plaster or steel picture hooks under 30 lb (14 kg), and plaster-rated anchors, studs or a rail system for anything heavier.
How much weight can a picture rail hook hold?
A typical picture rail hook from Picture Hang Solutions is rated for 25 lb (11 kg). The lowest-rated part of the system, hook, cord or molding, sets the limit, so use two hooks per frame and stay under the weakest rating.
Can you drill into tile to hang art?
Yes. Put a cross of painter's tape on the spot, use a carbide-tipped masonry bit at the drill's lowest speed with moderate pressure, and cool it with water. The screw must pass through the tile into a stud or backer board, which is what actually holds the weight.
What is the 4:1 safety rule for anchors?
Published anchor values are usually average ultimate loads, the point of failure. The accepted safe working load is 25% of ultimate, a 4:1 safety factor. So an anchor rated 720 lb ultimate should carry no more than about 180 lb.
How much weight can concrete block hold?
Less than solid concrete. Published Tapcon data for a 3/16 inch screw at 1 inch embedment gives 220 lb ultimate pull-out and 400 lb shear in lightweight block, and 340 lb and 730 lb in medium weight block. At 4:1, plan on 100 lb and 183 lb in shear.
Sources
- Confast, Technical Specifications for Tapcon Concrete Screws (ultimate values in concrete and block, bit sizes, embedment, 4:1 safety factor)
- Family Handyman, How to Hang Pictures on Plaster Walls (plaster keys, 16 lb and 30 lb thresholds)
- Bob Vila, How to Hang Picture Frames on a Brick Wall and How to Drill a Hole in Tile
- Picture Hang Solutions, Dos and Don'ts of Ogee Picture Rail Systems (25 lb rail hook rating, lowest component rule)
- Adams Brick Clips product specification (25 lb rating, brick height fit)
Published fastener values are averages for new, sound material and are offered as a guide, not a guarantee. For very heavy or valuable pieces, or walls in poor condition, have a professional installer assess the wall.
Cite this guide
Writers, framers, designers and students are welcome to quote this page. If you use one number, use this one:
A 3/16 inch concrete screw set 1 inch into 2,000 psi concrete has an average ultimate shear value of 720 lb; at the standard 4:1 safety factor, plan on about 180 lb per screw.
Suggested citation:
Austin Gallery, "How to Hang Art on Brick, Plaster, Tile and Concrete: The 4:1 Rule," updated November 2026. https://www.austingallery.org/blog/how-to-hang-art-on-brick-plaster-tile-and-concrete
More free charts: the Austin Gallery reference library.