Printmaking · Reference
Etching vs Engraving: The Tapered Line Test, Explained
An engraving is cut into a metal plate by hand with a burin, so its lines swell and taper to a point. An etching is drawn through an acid-resistant ground and bitten into the plate by acid, so its lines keep an even width and end bluntly. Both are intaglio prints, and both usually show a plate mark pressed into the paper around the image.
By Travis Moher · Published November 17, 2026
Etching and engraving get used as if they were the same word, and on dealer listings and frame shop tags they often are. They are not. The difference is how the line got into the metal: a hand-pushed blade or an acid bath. That difference leaves visible evidence on the paper, and once you know where to look you can usually tell them apart with a magnifier in under a minute. It is worth doing on any print you buy, frame or insure, because the technique affects how a print is described and valued.
The tapered line test
The single most useful check is the end of a line. A burin is pushed through copper like a plow, so the line starts thin, swells as the engraver presses, and thins to a point as the tool lifts out. Acid has no such motion: it bites the whole exposed line at once to roughly the same depth. The Folger Shakespeare Library's guide puts it plainly: engraved lines flow smoothly and typically swell before tapering to a point, while etched lines keep the same width along their length and have rounded ends. The University of Melbourne Library adds the other half of the picture: engraved lines are firm and constant even when they swell, while etched lines are softer and very slightly wobbly, because an etcher draws through wax almost as freely as with a pencil.
Two cautions. Etchers could make lines swell if they worked at it, and many plates mix both techniques, often engraving for the main figures and etching for backgrounds. Check several lines in different parts of the image before you decide.
Intaglio processes compared
Intaglio covers every technique where the image is sunk into the plate and the ink sits in the recesses. After inking, the surface is wiped clean and the plate goes through a press under heavy pressure, which forces the paper into the lines. Tate's glossary groups engraving, etching and drypoint here; aquatint and mezzotint are intaglio methods for tone rather than line.
| Process | How the plate is made | What the print looks like | Dates and notes |
|---|---|---|---|
| Engraving | Lines cut by hand with a burin; no acid | Firm lines that swell and taper to a point | Prints from engraved plates from about 1430, Germany |
| Etching | Needle drawn through an acid-resistant ground; acid bites the lines | Even-width, slightly wavering lines with blunt or rounded ends | Not dated by our sources |
| Drypoint | Scratched directly with a sharp needle; no acid | Soft, velvety, fuzzy-edged lines from ink caught in the burr | Small editions: the burr wears down |
| Aquatint | Rosin grains fused to the plate; acid bites around them | Grainy tone like a wash, not lines | Developed in France in the 1760s |
| Mezzotint | Plate roughened with a toothed rocker, then burnished smooth | Soft gradations from deep velvety black to light | Developed in the 17th century |
Definitions and dates from Tate's art terms glossary and the Print Club of Cleveland glossary. Line descriptions from the Folger Shakespeare Library and the University of Melbourne Library.
Relief vs intaglio vs planographic vs stencil
Every traditional print belongs to one of four families, defined by where the ink sits on the printing surface. The Print Club of Cleveland glossary describes relief as printing from a surface standing above the rest of the block, intaglio as lines sunk into the plate, and planography as a design on a flat surface with no perceptible variation in depth. A stencil print pushes ink through open areas.
| Family | Where the ink sits | Examples | What to look for |
|---|---|---|---|
| Relief | Raised surface carries the ink; cut-away areas print blank | Woodcut, linocut | Ink sits on the paper surface; crossing lines can look jagged where white was cut away |
| Intaglio | Ink sits in recessed lines or pits; surface wiped clean; heavy press | Engraving, etching, drypoint, aquatint, mezzotint | Plate mark around the image |
| Planographic | Flat surface, no depth; grease and water separate image from blank | Lithography, some monotypes | No cut or bitten lines and no recessed-plate mark |
| Stencil | Ink forced through open areas of mesh or a cut stencil | Screenprint (serigraph), pochoir | Flat areas of color with no plate mark |
The What to look for column is our gallery checklist, built from the definitions above and the Folger guide. Trimmed margins, mixed techniques and modern reproductions can all defeat a single test.
Modern editions add a fifth thing to rule out: digital reproduction. A giclee is an inkjet print, not a hand pulled one, and it can imitate the look of any of these families. Our sibling guide on giclee vs lithograph vs screenprint covers how to tell them apart, and what a giclee is explains the process itself.
How to tell them apart on a real print
- Find the plate mark. A rectangular dent around the image means a metal plate went through an intaglio press. The Folger notes the edge often carries traces of unwiped ink. No plate mark points to relief, lithography, screenprint or trimmed margins.
- Read the line ends. Tapered points suggest engraving; blunt, rounded ends suggest etching.
- Look for fuzz. A soft, velvety halo along the lines is the burr of a drypoint.
- Look at the tone. A grainy, wash-like tone is aquatint. Smooth gradations into a deep, velvety black are mezzotint. Tone built only from many fine lines and cross-hatching points to engraving.
- Check crossings. Where lines cross, intaglio lines flow through smoothly; in a woodcut the crossings can look jagged because the white diamonds between them were cut away.
Exceptions and distinctions
- •Wood engraving is cut in wood, not metal. It uses the same burin on a wood block, and Tate distinguishes it from woodcut, where the background is cut away instead. A label reading wood engraving describes a block print, so do not expect a metal plate mark.
- •A plate mark is not proof of age or originality. It only proves a plate. Later restrikes from old plates carry one too.
- •Photoengraving uses acid. Despite the name, Tate notes photoengraving etches a photographic image into metal, so it is closer to etching than to burin engraving.
- •Drypoint editions are short. The burr flattens with each pass through the press, so late impressions lose their velvet. This affects value more than in other intaglio techniques.
- •Mixed plates are common. Labeling a print etching and engraving, or etching with aquatint, is often the accurate description, not hedging.
Making your own plates? Intaglio needs a rolling etching press, because the pressure required is far higher than for relief printing. Our printmaking press buying guide explains bed size and pressure, and our ranking of the best etching and printmaking presses compares current models. For how editions are numbered and signed, see limited edition prints explained.
Free to use
Put this intaglio chart on your site
Selling prints, teaching printmaking or writing a collecting guide? Embed our etching vs engraving chart for your readers. Copy the snippet below; it renders a clean table anywhere. The only ask: keep the small credit link to Austin Gallery.
Click inside the box, select all (Cmd+A or Ctrl+A), and copy. Includes one credit link back to this page.
Frequently asked questions
What is the difference between etching and engraving?
Both are intaglio prints made from lines sunk into a metal plate. In engraving the artist cuts the lines by hand with a burin, a chisel-like tool. In etching the artist draws through an acid-resistant ground with a needle and acid bites the exposed lines into the plate. Engraved lines swell and taper to a point; etched lines keep an even width and end bluntly.
How can you tell if a print is an etching or an engraving?
Look at the line ends with a magnifier. The Folger Shakespeare Library notes that engraved lines flow smoothly and typically swell before tapering to a point, while etched lines tend to look shakier, keep the same width and have rounded ends. Check several lines, since many plates combine both techniques.
What is a plate mark on a print?
A plate mark is the rectangular indentation pressed into the paper by the edge of a metal plate under the heavy pressure of an intaglio press. It marks engravings, etchings, drypoints, aquatints and mezzotints. It can be missing if the margins were trimmed, and its presence alone does not prove a print is old or original.
Is drypoint an etching or an engraving?
Neither, strictly. Drypoint is its own intaglio technique: the artist scratches directly into the plate with a sharp needle and no acid. The scratch throws up a ridge of metal called a burr that holds ink and prints a soft, velvety line. Tate notes drypoints are usually printed in small editions because the burr wears down under the press.
What is the difference between aquatint and mezzotint?
Both make tone rather than line. Aquatint, developed in France in the 1760s according to Tate, fuses powdered rosin to the plate and lets acid bite around the grains, giving a grainy tone like a wash. Mezzotint, developed in the 17th century, roughens the whole plate with a toothed rocker and the artist burnishes it smooth to make lighter areas, giving soft gradations and velvety blacks.
What are the four main types of printmaking?
Relief, where the raised surface carries the ink (woodcut, linocut); intaglio, where ink sits in recessed lines (engraving, etching, drypoint, aquatint, mezzotint); planographic, where the image is printed from a flat surface (lithography); and stencil, where ink passes through open areas (screenprint).
When were engravings first used to make prints?
Tate dates the first prints from engraved metal plates to around 1430 in Germany. Metal engraving itself is far older and was used to decorate objects in classical antiquity.
Is a lithograph an etching?
No. A lithograph is planographic: it is printed from a flat stone or metal plate using the fact that grease and water do not mix, so there are no cut or bitten lines and no plate mark from a recessed plate. Etching is intaglio, printed from lines bitten into metal.
Sources
- Tate, Art Terms: intaglio, engraving, etching, drypoint, aquatint, mezzotint and lithography
- Print Club of Cleveland, Glossary of Printmaking Terms (relief, intaglio, planography, screenprint)
- Folger Shakespeare Library, The Collation: Woodcut, engraving, or what? (plate marks, line ends, crossings)
- University of Melbourne Library, Methods of intaglio printing: engraving versus etching
Identification notes are general guidance. Attributing a specific print, state or edition, especially an old master print, calls for a specialist examining the sheet in person.
More gallery reference guides
Cite this guide
Writers, framers, designers and students are welcome to quote this page. If you use one number, use this one:
Engraved lines are cut with a burin and swell before tapering to a point, while etched lines are bitten by acid and keep an even width with blunt, rounded ends; both are intaglio prints and usually show a plate mark.
Suggested citation:
Austin Gallery, "Etching vs Engraving: The Tapered Line Test, Explained," updated November 2026. https://www.austingallery.org/blog/etching-vs-engraving
More free charts: the Austin Gallery reference library.